2006 500 ranger belt or tranny problem

kenny fetty · 2011-01-07 19:42:34

hey guys i am new here.
so i have a rnger 500 side by side
my problem is when i put it in high or low and take off it doesnt engege all the way it starts off slow like a lower gear then kicks in wer eit is soppse to be...
ok say i am in low range i take off i give it gas and i am in the rev limter becase it is so low then after about 1 minute of this all of the sudden it kicks in to low ranges were it soppse to be..
so i have a new belt it still this this ... should i change the oil could it be stickin inside . in the gears amybe ..
any help
thanks .

Badley · 2011-01-07 21:37:49

Is your linkage out of adjustment? (or) Maybe the clutch primary is sticking.

kenny fetty · 2011-01-08 10:18:31

the primary is that the gear that goes in and out as u give it gas... if so it moves freely i take the belt off and see it go in and out as i give it throotel...
i am gogin to change all fluids today its been way over do i hope that helps

RANGERDALEXP · 2011-01-08 14:55:34

hey guys i am new here.
so i have a rnger 500 side by side
my problem is when i put it in high or low and take off it doesnt engege all the way it starts off slow like a lower gear then kicks in wer eit is soppse to be...
ok say i am in low range i take off i give it gas and i am in the rev limter becase it is so low then after about 1 minute of this all of the sudden it kicks in to low ranges were it soppse to be..
so i have a new belt it still this this ... should i change the oil could it be stickin inside . in the gears amybe ..
any help
thanks .

How many hours on the belt :?:
If the belt is good then it is either the primary or secondary clutch not working properly. Do a clutch service.....

kenny fetty · 2011-01-08 22:57:52

ok well i have the old belt and a brand ne wbelt they bopth do the same.
so today i took the primary/ closet to the front/ off and clean it up made sure it went in and out free and it did.. so when i put it toghter i notcied at real hig rev only the back pully would exspand the pully towrd the rear.. but you had to really rev it. so i took it off and could not even pull it apart by hand it was so tight so i took the c clip off and clean it out i think it had some old belt stuck in it were it couldent exspand..
now tommerw i will work on putting it back toghter i did tonight fo rhours and cant get the tension adjust rite.... it ehter exspand to easy or to tight ... i am tryign to get it back the way it was... i was close but low ranger was still to high ... but good news was the pully did exspand like it should
so i will let u no how it goes tommerw.

kenny fetty · 2011-01-11 20:12:06

let u no i got it fixed it was the back pully .. the littil slids on the inside of the pully behind the c clip are wore out so when it exspaned and then went back to normal it would lock there and would not exspand again.
so for now i just trun the slids around and now it works smooth as ever.
thanks

mbroyles · 2011-01-13 01:54:24

glad to hear you got your problem resolved.

Badley · 2011-01-13 19:49:50

Good job Kenny! Glad you found the problem.

#1 2011-01-07 19:42:34

Re: 2006 500 ranger belt or tranny problem

#2 2011-01-07 21:37:49

Re: 2006 500 ranger belt or tranny problem

#3 2011-01-08 10:18:31

Re: 2006 500 ranger belt or tranny problem

#4 2011-01-08 14:55:34

Re: 2006 500 ranger belt or tranny problem

#5 2011-01-08 22:57:52

Re: 2006 500 ranger belt or tranny problem

#6 2011-01-11 20:12:06

Re: 2006 500 ranger belt or tranny problem

#7 2011-01-13 01:54:24

Re: 2006 500 ranger belt or tranny problem

#8 2011-01-13 19:49:50

Re: 2006 500 ranger belt or tranny problem

Board footer